News News
Product center / Products
Contact us

Tel: 86 021-57360069

Fax: 86 021-57200778

Mobile: 13916306473 Aaron Du

China · Shanghai

Address:No.1285,Jinshi North Road,Jinshan District,Shanghai, China

Precautions for use in cold bending equipment

Date: 2017-03-24
Views: 11

With the continuous development of China's industry, cold-formed technology has also been rapid development. Cold-bending equipment has become an indispensable machinery for some professional factories. Then the use of cold-bending equipment also need to pay attention to the place.

First of all to choose the flat table, a steady machine, you can pull the chassis feet to facilitate the observation of the machine panel. Insert the plug on the hand-held head into the socket on the panel and tighten it, notice the notch.

Then plug the end of the power cord into the socket on the rear panel of the chassis and the other end into the power supply socket. Be sure to use single-phase three-wire power supply. And then open the power switch (POWER SW.) On the rear panel of the chassis. Press the "SWITCHING" button on the front panel, and the "Green" indicator will be ready for the "WARM UP" indicator. Press and hold the "SETTING BUTTON" button to set the appropriate value, usually between 0.5 and 2.0 seconds.

Press the start button on the handle, then the "HEATING" red indicator light, that is heating, the sensor head do not move away, "HEATING" red light off And then remove the sensor head.

Finally, the "WARM UP" green indicator light or the buzzer in the machine shorts the "beep" prompt and then the next container can be closed. Check the sealing quality, according to different materials, diameter containers and production efficiency, appropriate dressing "SET button (SETTING BUTTON) button, making the best sealing quality.


News More>
1
2017 - 03 - 22
The wire must be considered for oxidation, in order to prevent the formation of plastic deformation is not uniform to avoid failure in the course of the operationAs the protective gas oxidation increases, the amount of deoxidized elements (such as silicon, manganese, titanium, etc.) in the wire increases correspondingly, and the strength of the weld metal is reduced. When the deoxidation element in the wire contains the most insufficient, causing the weld toughness to decline, but also may lead to welding defects (such as pores, etc.) generation.Welding hot-rolled steel, normalizing steel and ...
2
2017 - 03 - 24
With the economic development, more and more families to buy a car, in order to car safety, have a good garage door, is expected by most families, then the garage door equipment produced by the garage door which is divided into several , That kind of better? Let Xiaobian to tell you:Electric (copper) garage doorAluminum alloy solid wood structure of the garage door, due to the characteristics of wood by climate and other environmental impact, cracking is inevitable. Although it can be dried by drying, paint and other processes to reduce cracking, but can not be completely avoided. The copper g...
3
2017 - 03 - 24
Integrated wall equipment is the production of integrated wall of the main equipment for the decoration industry is very important, generally integrated wall of the advanced production technology, equipment, low loss, the production of integrated wall yield is also high. With integrated wall equipment to produce integrated wall with no radiation, no formaldehyde production, fire, water, moisture, no smell, easy to scrub, super hardness, fashion bright, easy installation and so on many excellent features.Sang flash is your choice to buy integrated wall equipment, Shanghai Sang flash Machinery C...
4
2017 - 03 - 24
Integrated wall equipmentProduction of integrated wall equipment is called integrated wall equipment, for the decoration industry is very important, generally integrated wall of the advanced production technology, equipment loss is low, the production of integrated wall yield is also high. With integrated wall equipment to produce integrated wall with no radiation, no formaldehyde production, fire, water, moisture, no smell, easy to scrub, super hardness, fashion bright, easy installation and so on many excellent features.Cold bending equipmentCold bending equipment is a kind of including shel...
5
2017 - 03 - 24
With the development of the economy, more and more families have bought a car, for the safety of the car, have a good garage door, which is expected by most families, then which garage door equipment produced by the garage door is good? Customers should choose someone's garage door equipment?Xiao Bian that Shanghai Sang flash Machinery Co., Ltd. is a good choice. Shanghai Sang flash Machinery Co., Ltd. is one of the few, with the international outstanding cold-formed steel roll design software Germany COPRA software professional company. The company has many years of business history, the stre...
6
2017 - 03 - 24
Now the real estate industry is developing very rapidly, and led all kinds of manufacturing and construction of the rapid development of the industry. Take the integrated wall for it, although it is only in recent years appeared in the market, but the lightning speed of the rapid occupation of the decoration market of the big river, and in a leading position. This product has a very good sound insulation effect, hard texture, as the decoration of the wall material is very applicable. But it also requires integrated wall equipment with good quality, to be able to produce a good integrated wall ...

Tell me your needs, we will contact you the first time!

Address:No.609,Jinzhang Highway,Jinshan District,Shanghai, China   Tel: 86 021-57360069
Copyright ©2017 - 2020 Shanghai Sunshine Machine Co.,Ltd
犀牛云提供云计算服务