China · Shanghai

Address:No.1285，Jinshi North Road，Jinshan District,Shanghai, China

Precautions for use in cold bending equipment

Date: 2017-03-24

Share to:

With the continuous development of China's industry, cold-formed technology has also been rapid development. Cold-bending equipment has become an indispensable machinery for some professional factories. Then the use of cold-bending equipment also need to pay attention to the place.

First of all to choose the flat table, a steady machine, you can pull the chassis feet to facilitate the observation of the machine panel. Insert the plug on the hand-held head into the socket on the panel and tighten it, notice the notch.

Then plug the end of the power cord into the socket on the rear panel of the chassis and the other end into the power supply socket. Be sure to use single-phase three-wire power supply. And then open the power switch (POWER SW.) On the rear panel of the chassis. Press the "SWITCHING" button on the front panel, and the "Green" indicator will be ready for the "WARM UP" indicator. Press and hold the "SETTING BUTTON" button to set the appropriate value, usually between 0.5 and 2.0 seconds.

Press the start button on the handle, then the "HEATING" red indicator light, that is heating, the sensor head do not move away, "HEATING" red light off And then remove the sensor head.

Finally, the "WARM UP" green indicator light or the buzzer in the machine shorts the "beep" prompt and then the next container can be closed. Check the sealing quality, according to different materials, diameter containers and production efficiency, appropriate dressing "SET button (SETTING BUTTON) button, making the best sealing quality.

Previous：NoneNext：Polyurethane phenolic insulation board e

News More>

The mandrel manufacturer tells you what is precision machining

2017 - 03 - 22

1 micron machining method. Precision machining is done under tightly controlled environmental conditions using precision machine tools and precision gauges and gauges. Processing accuracy to achieve and more than 0.1 micron ultra-precision machining. In the aerospace industry, precision machining is mainly used for machining precision mechanical parts in aircraft control equipment, such as precision fittings in hydraulic and pneumatic servos, gyroscope frames, housings, flotation, liquid-filled bearing assemblies and Floats and so on. The precision parts of the aircraft are complex, the rigidi...

The elongated shaft machining supplier tells you the advantages of the hollow shaft

2017 - 03 - 22

Hollow shaft is more and more people to use, then let's talk about what the advantages of what you loved by everyoneHollow shaft occupies a relatively large volume of space, but can reduce the weight. According to the mechanical analysis of materials, in the shaft transmission torque, from the radial section to see, the more the place outside the effective torque transmission effect. In the shaft need to pass a larger torque, you need a thick shaft diameter. And because the role of the torque in the axial parts of the smaller, so the general use of hollow to reduce the weight of the shaft.

Continuous casting roll manufacturers to remind you must consider the oxidation of wire

2017 - 03 - 22

The wire must be considered for oxidation, in order to prevent the formation of plastic deformation is not uniform to avoid failure in the course of the operationAs the protective gas oxidation increases, the amount of deoxidized elements (such as silicon, manganese, titanium, etc.) in the wire increases correspondingly, and the strength of the weld metal is reduced. When the deoxidation element in the wire contains the most insufficient, causing the weld toughness to decline, but also may lead to welding defects (such as pores, etc.) generation.Welding hot-rolled steel, normalizing steel and ...

Garage door equipment produced by the garage door type

2017 - 03 - 24

With the economic development, more and more families to buy a car, in order to car safety, have a good garage door, is expected by most families, then the garage door equipment produced by the garage door which is divided into several , That kind of better? Let Xiaobian to tell you:Electric (copper) garage doorAluminum alloy solid wood structure of the garage door, due to the characteristics of wood by climate and other environmental impact, cracking is inevitable. Although it can be dried by drying, paint and other processes to reduce cracking, but can not be completely avoided. The copper g...

Buy integrated wall equipment on the election Sang flash

2017 - 03 - 24

Integrated wall equipment is the production of integrated wall of the main equipment for the decoration industry is very important, generally integrated wall of the advanced production technology, equipment, low loss, the production of integrated wall yield is also high. With integrated wall equipment to produce integrated wall with no radiation, no formaldehyde production, fire, water, moisture, no smell, easy to scrub, super hardness, fashion bright, easy installation and so on many excellent features.Sang flash is your choice to buy integrated wall equipment, Shanghai Sang flash Machinery C...

What is the difference between integrated wall equipment and cold - formed equipment?

2017 - 03 - 24

Integrated wall equipmentProduction of integrated wall equipment is called integrated wall equipment, for the decoration industry is very important, generally integrated wall of the advanced production technology, equipment loss is low, the production of integrated wall yield is also high. With integrated wall equipment to produce integrated wall with no radiation, no formaldehyde production, fire, water, moisture, no smell, easy to scrub, super hardness, fashion bright, easy installation and so on many excellent features.Cold bending equipmentCold bending equipment is a kind of including shel...